Hmm, the TS100 can't pump enough heat into the joints between the two PCBs (at least for the ground plane connections). Gonna have to bring out my old, less fancy but higher thermal mass iron.

I did a quick comparison of the sound of a few different #trackball models - the Microsoft Trackball Explorer, Elecom Huge, Ploopy and a quick test part

The Microsoft and Elecom ones have very low "stiction" at low speeds which is really nice. The Ploopy is great at high speeds but slightly frictiony at low speeds depending on direction. Hoping I can mod the design to fit silicon nitride bearings into it!

I designed some quick bearing mounts for the Ploopy trackball today - instead of roller bearings I wanted to use silicon nitride ball bearings. They don't rotate, they're just a low friction surface.

Rather than re-printing the entire massive top part of the trackball, I chose to just make them small "adapter" inserts that you can put into the bearing holders in the existing part.

Anyway, last night I printed the trackball bearing mounts and fitted them into the trackball. They needed a little bit of filing and drilling to get them to fit right, but they work well!

I used the trackball all day today and it's definitely a small improvement over the roller bearings. Unfortunately the snooker ball is too rough so there's about as much friction as before. It's nicer though because it's the same in all directions!

One of the mounts (the one closest to the camera) needed to be reshaped a bit to fit - the pocket is a slightly different shape. But I'm kinda shocked my first attempt works so well!

I ordered an alternative ball for the #ploopy trackball. It was sold for a Logitech cordless optical trackman and is a bit smaller but still works.

Using it with my silicon nitride bearings with an adapter, it was surprisingly not much of an improvement over the pool ball. However, once I put the original roller bearings back in, it makes a huge difference! There's now very little friction to overcome when going from stopped to moving, which makes precise movements a hell of a lot easier.

So to summarise the current best setup I have for the Ploopy #trackball - Use the original bearings and just replace the ball with a glossy one.

I've been talking with someone on reddit about modding ball transfer units into the #Ploopy #trackball. They're basically omnidirectional ball bearings.

It was kind of hard to source the small ones in the UK (seem to be available mostly to companies, but I have no VAT number) but I got some eventually.

Here's a quick video comparing them in a test part to the Ploopy's stock bearings: imgur.com/a/Y7NeHqx

How's this for a computer peripheral aesthetic?

This is the first stage of a mod for the Ploopy trackball to use ball transfer units (BTUs) as bearings for the ball.

This just about fits in the shell and feels good, so the next step is to try to modify the CAD file for the original shell.

I'm quite enjoying the ball transfer units in the trackball. They're the lowest friction bearing option I've tried. That means you can flick from one side of a bunch of screens to the other, but it also means it's easier to be precise.

With high static friction, it's hard to overcome it to do a small movement without overdoing the movement.

Yesterday I did a third iteration of the BTU mod for the Ploopy #trackball

I cut off just the front section and printed it today - my supports were a bit excessive so just that bit took 7 hours!

I've been using it this evening and it feels good. I moved the bearings a bit further up the walls so it's harder to push the ball sideways by accident.

The trackball print finished in 12.5 hours instead of 13.5, so now I have the world's ugliest trackball!

Also that was a lot of support material - probably could have turned that down a bunch.

@gbrnt which ball transfer units are you using there?

It looks great!

@ekaitz_zarraga Thanks! They're Bosch-Rexroth R053010810. They were actually a bit hard to find a good supplier for in the UK (even before Brexit finished) unless you're a company.

If it would be helpful I can list some of the suppliers someone on reddit found.

@gbrnt I am a company :D

(and I'm not in the UK LOL)

Isn't Alwayse a british company? it may be easier to buy the bearings there...

@gbrnt wow 14 bucks of shipping fee... omg

:D

But they are pretty cheap and look very cool. I should find a way to get them.

@ekaitz_zarraga I had a fun one with livhaven where it was $30 for the parts and something like $130 for shipping!

@gbrnt
That's a good one ahahah

PS: I think I found these little guys in Spain!!! Yay!

@ekaitz_zarraga Nice! An alternative name to look for is KU-B8-OFK. What's the site you found, so I can add it to my list?

I'm planning on writing up a blog post about this once I've done one more iteration of the design.

Sign in to participate in the conversation
Mastodon

Server run by the main developers of the project 馃悩 It is not focused on any particular niche interest - everyone is welcome as long as you follow our code of conduct!